Description
Rectangular power button (switch) S125 / HLT-126W (6(4)A 250V, with capacitor slot, 35×25×20 mm) for angle grinders
The double-pole trigger switch (power button) marked S125 (structural analog of HLT-126W, rated 6(4) A / 250 V AC, service life 5E4 — 50,000 cycles) is designed for switching the mains power of commutator electric motors in compact angle grinders (115–125 mm disc grinders), orbital sanders, and other mains-powered electric tools with a power rating up to 1000–1200 W. The button is housed in a rectangular body made of heat-resistant polyamide measuring 35 × 25 × 20 mm and is equipped with a plunger (trigger) featuring an elastic silicone dust cap that prevents the mechanism from jamming due to abrasive concrete and metal dust. The mechanism operates on a DPST (2 normally open contacts 1–1 and 2–2) circuit with mechanical latching in the "on" position (turned off by pressing the grinder's external housing lever again). The bottom of the housing features a special integrated holder pocket with latches for installing a mains noise suppression capacitor.
Key Advantages and Features:
- Dust-protected silicone cap on the plunger: The sealed elastic boot reliably protects the trigger stem from fine dust and shavings entering the contact group during concrete, brick, and metal cutting.
- Integrated capacitor compartment: A special plastic pocket with latches and four brass connection slots (quick-connect terminals for stator and capacitor leads) allows for a compact placement of the noise suppression capacitor directly on the switch body.
- Combined connection (screws + quick-connect slots): The mains power cord input is secured by reliable screw terminals with pressure plates, while the stator and capacitor wires are inserted into spring-loaded internal contacts without soldering.
- Double-pole circuit break (contacts 1–1 and 2–2): When switched off, the button simultaneously disconnects both the phase and neutral lines, ensuring maximum electrical safety when replacing a cutting disc.
- Increased operating life (5E4): Reinforced silver-containing contacts are rated for 50,000 on-off cycles under a 6(4) A load at 250 V.
Compatibility and Application:
The switch is used in domestic and semi-professional angle grinders (115 / 125 mm) with a slider or lever power system on the housing (where an external plastic lever presses the latching button plunger), as well as in sanders and jigsaws, provided the dimensions 35 × 25 × 20 mm match:
- Compatible power tool brands: Bosch (GWS 6-115 / 7-115 / 850 series and analogs), Makita (GA5030 / 9555 / 9558 series — replicas and analogs), Interskol, Fiolent, Zenit, Elprom, Ritm, Vityaz, Proton, Craft-Tec, Vorskla, Dnipro-M, Forte, Vitals, Sturm, Einhell, Ferm, Stern, DWT, Sparky.
- Marking / Cross-codes: S125, HLT-126W, FA2-6/2B (in rectangular version with 35×25×20 mm capacitor compartment).
Technical Specifications:
| Parameter | Value / Characteristic |
|---|---|
| Component type | Power tool trigger switch (power button) |
| Marking / Model | S125 (analog of HLT-126W) |
| Rated current and voltage | 6(4) A / 250 V AC (~50/60 Hz) |
| Contact scheme | Double-pole (DPST, 2 normally open contacts 1–1 and 2–2) |
| Position locking | Latching (press to turn on, press again to turn off) |
| Wire connection type | 2 screw terminals (mains cable) + 4 internal quick-connect slots (stator and capacitor) |
| Housing dimensions (L×W×H) | 35 × 25 × 20 mm (excluding rubber plunger height) |
| Design features | Dust cap on the button + integrated capacitor holder compartment |
| Condition | New spare part (supplied without capacitor) |
Package Contents:
- S125 / HLT-126W trigger button (35×25×20 mm) — 1 pc.
Pro Tip: Before dismantling the old button, be sure to unplug the grinder from the 220 V socket and take a photo of the wire layout: the mains power cord connects to the upper screw terminals, while the stator coil leads and noise suppression capacitor pins are inserted into the lower internal quick-connect slots (to remove an old wire from a quick-connect slot, insert a thin awl or needle into the adjacent service hole and release the locking tab). When installing the new button into the grinder housing, check the free travel of the external lever — it should clearly press and release the rubberized plunger without binding.




